汽车发动机用AZ91D合金的表面喷涂与性能

采用热喷涂工艺在压铸态AZ91D合金表面制备了Al涂层,研究了热处理温度和保温时间对AZ91/Al涂层界面组织形貌的影响,并对比分析了扩散层的耐腐蚀性能和耐磨性能。结果表明,热处理前Al涂层与基材为机械结合,热处理后Al涂层与AZ91合金基材的界面处可形成冶金结合扩散层,且随着保温时间延长,扩散层厚度不断增加;热处理温度在375 ℃以下时扩散层主要由β-Mg₁₇Al₁₂相构成,375 ℃×8 h热处理后为α-Mg+β-Mg₁₇Al₁₂相,425 ℃×1 h热处理后为γ-Mg₂Al₃和β-Mg₁₇Al₁₂相。AZ91合金基材和扩散层腐蚀电位从高至低顺序为γ>β>α+β>AZ91合金基材,扩散层的腐蚀电流密度均低于AZ91合金基材,阻抗谱图中容抗弧半径从大至小顺序为γ>β>α+β>AZ91合金基材,扩散层的耐腐蚀性能均优于AZ91合金基材;γ、β和α+β扩散层的摩擦稳定性系数都高于AZ91合金基材,而磨损速率和磨痕宽度都要小于AZ91合金基材,其中β扩散层的磨损速率和磨痕宽度最小,具有最佳的抵抗磨损的能力。     

Ni,Cr, and Fe surfaces corroded by molten ZnCl2

Understanding the corrosion of molten ZnCl₂ on metal surfaces is significant for the corrosion protection of metals, sustainable use of molten salts, preparation of ZnO coatings, and so on. In this paper, surfaces of pure Ni, Cr, and Fe corroded by molten ZnCl₂ were investigated. The results show that Ni suffered very slight corrosion, while Cr experienced more serious corrosion than Ni, but lighter corrosion than Fe. The morphology of the corrosion of Cr and Fe, respectively, presented pitting and intergranular corrosion characteristics. Furthermore, nanostructured ZnO coatings were obtained on the surfaces of Ni and Fe, but not on the surface of Cr. The ZnO coating on the Ni surface was doped with a small amount of Zn₅(OH)₈Cl₂, and the ZnO coating on the Fe surface was doped with ZnFe₂O₄ and Zn₂OCl₂. The coatings on the Ni and Fe surfaces had an average thickness of 1.5 and 50 μm, respectively.     

化学气相沉积钨涂层的研究现状与进展

化学气相沉积钨涂层具有工艺简单、技术成熟度高、涂层综合质量优异等特点，广泛应用于国防、航天、核工业等领域。首先介绍了化学气相沉积钨涂层的原理和特点，重点讨论了化学气相沉积钨涂层的工艺及应用研究现状，包括化学气相沉积钨涂层微观组织控制工艺及在耐辐射、耐磨耐蚀和高温防护领域的应用，同时对新型化学气相沉积钨涂层技术的发展进行了展望。一是改善现有工艺存在的反应气源与反应产物毒性大等问题，满足绿色环保的发展要求；二是改善现有工艺存在的沉积温度高、沉积速率偏低等问题，实现在不同衬底表面的高效、高质量沉积；三是改善现有化学气相沉积钨涂层结构与功能单一等问题，满足构件对钨涂层高性能和多功能的需求。     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

Formation of a protective layer against corrosion on Mg alloy via alkali pretreatment followed by vanillic acid treatment

Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy.     

Optical spectroscopic and electrochemical characterization of oxide films on a ferritic stainless steel

Colored oxide films that form on ferritic stainless steel in a high-temperature, oxidizing environment and correspond to different chemical compositions can cause a deterioration of pitting resistance and corrosion performance. Herein, optical spectroscopic and electrochemical techniques have been used to reveal the relationship between color, chemical composition, and corrosion resistance of oxide films formed in the temperature range from 400°C to 800°C for 30 min and at 800°C for 10, 20, 30, and 60 min. The substrate with a thin and dense passivation film leads to a low pitting potential but high corrosion resistance. Oxide films of yellowish or brownish color formed below 600°C are mainly iron oxides, which correspond to low corrosion resistance. No passivation characteristics can be observed for polarization curves of oxide films formed at 500°C and 600°C. The color of oxide films varies from blue to dark gray with the increase of oxidation time at 800°C. Corrosion resistance changes with different proportions of Fe₃O₄, Cr₂O₃, and FeCr₂O₄. The gray oxide films formed at 800°C for 30 min exhibit the lowest pitting susceptibility and the highest corrosion resistance.     

某油田油井采出水腐蚀因素研究

我国油田油井生产中采油井管柱腐蚀现象十分普遍,所以在注CO_2驱进行开采过程中要进行采出水的质量分析。对现阶段的油田生产腐蚀及防腐技术进行论述,提出相对应的防腐措施,进一步为油田生产作业提高产量。